Medical oil-free air compressor

Adsorption dryer

Adsorption dryer

  • introduce

Adsorption dryer

Adsorption dryer is through the "pressure change "(pressure change adsorption principle) to achieve the drying effect. Due to the ability to hold water vapor and air pressure is inversely proportional to its part of the dry air (called again angry) decompression expansion to atmospheric pressure, the pressure change make expansion air more dry, then let it flow through turn on the air must be regenerated desiccant layer (i.e., have to absorb enough water vapor drying tower), the water in the dry gas sucked out desiccant, it out of the dryer to achieve the goal of dehumidifying. The two towers work in a cycle, without heat source, continuously providing dry compressed air to the user's gas system.

The absorber is classified according to the adsorbent regeneration mode, which can be mainly divided into two kinds: non-thermal regeneration micro-thermal regeneration absorber and thermal regeneration micro-thermal regeneration absorber. Because there is no heat micro-heat regenerative drying machine is based on isothermal adsorption work, also known as "pressure swing adsorption" heat micro-heat regenerative drying machine is based on isothermal adsorption work, also known as "temperature swing adsorption". In practical use there is a kind of called micro-heat dryer, from the form, micro-heat regenerative dryer is also the regeneration gas heating, but because it is used in the regeneration gas is from its own moisture content is very low dry air, so it is also a "pressure swing adsorption" dryer.

Table of technical specifications for adsorption dryer


LBX—1.0

LBX—2.0

LBX—3.0

LBX—6.0

LBX—10

LBX—15

Rated air

handling

capacity

(Nm³/min)

1

2.4

3.8

6.5

13.5

18

Pressure

of work

(PMa)

0.4—1.0

0.4—1.0

0.4—1.0

0.4—1.0

0.4—1.0

0.4—1.0

Inlet

temperature

(℃)

≤45

≤45

≤45

≤45

≤45

≤45

Intake

oil content

(ppm)

≤0.01

≤0.01

≤0.01

≤0.01

≤0.01

≤0.01

adsorbent

Aluminum

glue or

molecular

sieve

Aluminum

glue or

molecular

sieve

Aluminum

glue or

molecular

sieve

Aluminum

glue or

molecular

sieve

Aluminum

glue or

molecular

sieve

Aluminum

glue or

molecular

sieve

Regenerative

way

No thermal regeneration(microthermo)

Way to work

The two towers work alternately

Gas

consumption

12%-15%(6%)

12%-15%(6%)

12%-15%(6%)

12%-15%(6%)

12%-15%(6%)

12%-15%(6%)

The control

mode

Conventional high power or single chip microcomputer control

Heater power

1

1.5

2

2.5

3

5

Drying

degree

of finished

product gas

Pressure dew point: -20℃~-40℃ (-40℃~70℃)

Dust

particle

size of

finished

product

≤0.01µm

≤0.01µm

≤0.01µm

≤0.01µm

≤0.01µm

≤0.01µm

Length

x width

x height

980×420×1200

1080×420×1550

1080×420×1550

1200×700×2050

1600×720×2420

1600×72×2420

Air inlet

and outlet

diameter

ZG1″ The tooth

DN25FL

DN25FL

DN40FL

DN50FL

DN80FL

installation

Erect flat floor mounting

The address of this article:http://en.wyysjzx.com/product/647.html

Key word:Adsorptiondryer,Adsorptiondryerfactory,Oilfreeaircompressor

last:None
next:None
  • 中文

  • 0412-8229898
  • Online Service